416 found, showing page 11 of 28
$47.996
2" DWV P-TRAP W/CLEANOUT
PVC Schedule 40 DWV. Used for the prevention of sewer gas entering the house through the plumbing fixture drain.
View Details
$21.698
1-1/2"PVC-DWV ADJ P-TRAP
PVC Schedule 40 DWV. Used for the prevention of sewer gas entering the house through the plumbing fixture drain.
View Details
$24.895
1-1/4 WHT PLASTIC S-TRAP
Replacement S-trap for bathroom lavatory drains, includes nuts and washers. White plastic. Bagged.
View Details
$29.878
1/2PINT PURPLE PRIMER
A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all schedules and diameters. Formulated to remove surface dirt, grease, and grime as well as soften the pipe surface to allow for a fast, secure, and permanent solvent weld. For use in areas where code calls for verification that a primer has been used. Recommended for all PVC and CPVC installations. NSF and UPC listed. Exceeds ASTM F-656.
View Details
$13.844
1-1/2" PVC-DWV WYE
PVC Schedule 40 DWV. PVC-DWV (hub x hub x hub).
View Details
$8.29
1-1/2" 22-1/2D DWV ELBOW
PVC Schedule 40 DWV. (1/16 bend), PVC-DWV (hub x hub).
View Details
$11.49
1-1/2" 60D PVC-DWV ELBOW
PVC Schedule 40 DWV. (1/6 bend), PVC-DWV (hub x hub).
View Details
$6.09
1-1/2" 45D PVC-DWV ELBOW
PVC Schedule 40 DWV. (1/8 bend), Short radius. PVC-DWV (hub x hub).
View Details
$8.813
1-1/2" CLEANOUT W/PLUG
PVC Schedule 40 DWV. PVC-DWV (spigot x F.I.P.).
View Details
$8.29
1-1/2" DWV SANITARY TEE
PVC Schedule 40 DWV. PVC-DWV (hub x hub x hub).
View Details
$8.831
1-1/2X1-1/4 PVC ADP SPG
PVC Schedule 40 DWV. Combination 1-1/2" x 1-1/2" or 1-1/2" x 1-1/4". Fitting x slip jam nut. Fitting end fits into Schedule 40 fitting hub. 1-1/2" x 1-1/4".
View Details
$8.79
1-1/2X1-1/4 PVC ADP HUB
PVC Schedule 40 DWV. Hub x slip jamnut. Hub end fits over Schedule 40 pipe.
View Details
$21.99
2X1-1/2 FLEX COUPLING
Made of a tough elastomeric PVC compound that meets the requirements of ASTM No. D5926, are resistant to chemicals, ultraviolet rays, fungus growth, and normal sewer gases. Stainless steel clamps are corrosion-resistant and rust-proof. For use in sewer and drain, water, and vent piping. Maximum working pressure 4.3 P.S.I. (29.6 kPa); Maximum operating temperature: 140 deg. F. nonconsistent. A = the inside diameter (I.D.) of side No. 1. B = the inside diameter (I.D.) of side No. 2. C = the length of the actual coupling, end to end.
View Details
$10.49
1-1/4 WHT PLASTIC P-TRAP
1-1/4" x 1-1/4" P-trap. Includes slip-joint wing nuts and washer. Bagged.
View Details
$32.49
4" 22-1/2D PVC-DWV ELBOW
PVC Schedule 40 DWV. (1/16 bend), PVC-DWV (hub x hub).
View Details
